-
1 proprietes electriques
электрические свойства горной породы
Свойства, характеризующие возникновение, распределение, поглощение и преобразование электрического поля в горной породе.
[ ГОСТ Р 50544-93]Тематики
Обобщающие термины
EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > proprietes electriques
-
2 courant admissible, m
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Франко-русский словарь нормативно-технической терминологии > courant admissible, m
-
3 courant permanent admissible, m
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Франко-русский словарь нормативно-технической терминологии > courant permanent admissible, m
-
4 d’électricité (2)
электрический
Основанный на электрической технологии.
Примечания
1. Данный термин предназначен для того, чтобы охватить любое или все устройства, или системы, действующие на основе электричества.
2. В число электрических/электронных/программируемых электронных устройств входят:
- электромеханические устройства (электрические);
- полупроводниковые непрограммируемые электронные устройства (электроника);
- электронные устройства, основанные на компьютерных технологиях (программируемые электронные); см. 3.2.5.
[ ГОСТ Р МЭК 61508-4-2007]
электрический (1)
-
[IEV number 151-11-03]EN
electric, adj
containing, producing, arising from, or actuated by electricity
NOTE – Examples of usage of the term "electric": electric energy, electric lamp, electric motor, electric quantity.
[IEV number 151-11-03]FR
électrique, adj
contenant, produisant, provenant de, actionné par l'électricité
NOTE – Exemples d'emploi de l'adjectif "électrique": énergie électrique, lampe électrique, moteur électrique, grandeur électrique.
[IEV number 151-11-03]электрический (2)
-
[IEV number 151-11-05]EN
electrical (2), adj
pertaining to electricity, but not having its properties or characteristics
NOTE – Examples of usage of this concept: electrical handbook.
[IEV number 151-11-05]FR
d’électricité, qualificatif
relatif à l'électricité, mais n'ayant ni ses propriétés ni ses caractéristiques
NOTE – Exemples d'emploi de ce concept: manuel d'électricité.
[IEV number 151-11-05]EN
DE
- elektrisch (1)
- Elektro... (2) (in Zusammensetzungen)
FR
- d’électricité (2)
- électrique (1)
Франко-русский словарь нормативно-технической терминологии > d’électricité (2)
-
5 électrique (1)
электрический
Основанный на электрической технологии.
Примечания
1. Данный термин предназначен для того, чтобы охватить любое или все устройства, или системы, действующие на основе электричества.
2. В число электрических/электронных/программируемых электронных устройств входят:
- электромеханические устройства (электрические);
- полупроводниковые непрограммируемые электронные устройства (электроника);
- электронные устройства, основанные на компьютерных технологиях (программируемые электронные); см. 3.2.5.
[ ГОСТ Р МЭК 61508-4-2007]
электрический (1)
-
[IEV number 151-11-03]EN
electric, adj
containing, producing, arising from, or actuated by electricity
NOTE – Examples of usage of the term "electric": electric energy, electric lamp, electric motor, electric quantity.
[IEV number 151-11-03]FR
électrique, adj
contenant, produisant, provenant de, actionné par l'électricité
NOTE – Exemples d'emploi de l'adjectif "électrique": énergie électrique, lampe électrique, moteur électrique, grandeur électrique.
[IEV number 151-11-03]электрический (2)
-
[IEV number 151-11-05]EN
electrical (2), adj
pertaining to electricity, but not having its properties or characteristics
NOTE – Examples of usage of this concept: electrical handbook.
[IEV number 151-11-05]FR
d’électricité, qualificatif
relatif à l'électricité, mais n'ayant ni ses propriétés ni ses caractéristiques
NOTE – Exemples d'emploi de ce concept: manuel d'électricité.
[IEV number 151-11-05]EN
DE
- elektrisch (1)
- Elektro... (2) (in Zusammensetzungen)
FR
- d’électricité (2)
- électrique (1)
Франко-русский словарь нормативно-технической терминологии > électrique (1)
-
6 poste exterieur
открытая подстанция
Электрическая подстанция, оборудование которой расположено на открытом воздухе.
[ ГОСТ 24291-90]EN
outdoor substation
a substation which is designed and installed to withstand external weather conditions
[IEV number 605-02-16]
air-insulated substation
An electric power substation that has the busbars and equipment terminations generally open to air and utilizes insulation properties of ambient air for insulation to ground.
[ http://www.answers.com/topic/air-insulated-substation]FR
poste extérieur
poste conçu et installé pour supporter les conditions atmosphériques extérieures
[IEV number 605-02-16]Тематики
EN
DE
FR
Электрическая подстанция, оборудование которой расположено на открытом воздухе
605-02-16
de Freiluftstation
en outdoor substation
fr poste extérieur
Источник: ГОСТ 24291-90: Электрическая часть электростанции и электрической сети. Термины и определения оригинал документа
Франко-русский словарь нормативно-технической терминологии > poste exterieur
См. также в других словарях:
electric properties — elektrinės savybės statusas T sritis Standartizacija ir metrologija apibrėžtis Medžiagos gebėjimas praleisti elektros srovę bei poliarizuotis elektriniame lauke. atitikmenys: angl. electric properties; electrical properties vok. elektrische… … Penkiakalbis aiškinamasis metrologijos terminų žodynas
electric properties — elektrinės savybės statusas T sritis fizika atitikmenys: angl. electric properties; electrical properties vok. elektrische Eigenschaften, f rus. электрические свойства, n pranc. propriétés électriques, f … Fizikos terminų žodynas
Electric catfish — Malapterurus electricus Scientific classification Kingdom: Animalia … Wikipedia
Electric charge — SI symbol: Q SI quantity dimension: Q SI unit: coulomb other units: e Derivations from other quantities: Q = I · … Wikipedia
Electric gates — are an easy way to ensure the security of private premises and can be used for all sized properties. Electric gates, though not very commonplace at the moment, have found their niche in the market today. For those who find the security of their… … Wikipedia
Electric jacket — Electric jackets are jackets which exhibit properties similar to those possessed by electric blankets. They are most commonly used by motorcycle enthusiasts when temperatures are cold. They usually obtain power for their heating processes through … Wikipedia
Electric sonic amplitude — is an electroacoustic phenomena that is reverse to colloid vibration current. It occurs in colloids, emulsions and other heterogeneous fluids under influence of oscillating electric field. This field moves particles relative to the liquid, which… … Wikipedia
Electric field proximity sensing — or EFPS is a sensory system that relies on the fact that an electric field can be perturbed by the existence of a nearby object, provided it is at least slightly conductive.EFPS systems today are used in a wide variety of industrial and… … Wikipedia
Electric cell-substrate impedance sensing — or short ECIS refers to a non invasive biophysical approach to monitor living animal cells in vitro, i.e. within a well defined laboratory environment.Giaever Keese, A morphological biosensor for mammalian cells, Nature 366(1993)591 2] In ECIS… … Wikipedia
Electric double-layer capacitor — Maxwell Technologies MC and BC series supercapacitors (up to 3000 farad capacitance) An electric double layer capacitor (EDLC), also known as supercapacitor, supercondenser, electrochemical double layer capacitor, or ultracapacitor, is an… … Wikipedia
Properties of water — H2O and HOH redirect here. For other uses, see H2O (disambiguation) and HOH (disambiguation). This article is about the physical and chemical properties of pure water. For general discussion and its distribution and importance in life, see Water … Wikipedia
